Johnson Controls Bentel Security tyco ABS128M50, Руководство по установке

Страница: 60 / 132

A Arming Label Enter the message that the Keypads
should show when Type A Arming takes place, as
shown in Figure 28 ( 1 ) for the Touch keypad.
Valid entries: up to 16 characters.
Default: STAY type A.
B Arming Label Enter the message that the Keypads
should show when Type B Arming takes place, as
shown in Figure 28 ( 2 ) for the Touch keypad.
Valid entries: up to 16 characters.
Default: STAY type B.
C Arming Label Enter the message that the Keypads
should show when Type C Arming takes place, as
shown in Figure 28 ( 3 ) for the Touch keypad.
Valid entries: up to 16 characters.
Default: STAY type C.
D Arming Label Enter the message that the Keypads
should show when Type D Arming takes place, as
shown in Figure 28 ( 4 ) for the Touch keypad.
Valid entries: up to 16 characters.
Default: STAY type D.
LCD Keypad Standby Page Enter the message that
the LCD Keypads should show in standby status.
Valid entries: up to 16 characters.
Default: BENTEL ABSOLUTA.
A Arming Description Insert a text that describes
arming Type A : this text will be shown in the Touch Key-
pad when the corresponding arming is selected, as
shown in Figure 28 (
6 ).
Valid entries: up to 128 characters.
Default: empty.
B Arming Description Like “A Arming Description”
but for arming type B.
Valid entries: up to 128 characters.
Default: empty.
C Arming Description Like “A Arming Description”
but for arming type C.
Valid entries: up to 128 characters.
Default: empty.
D Arming Description Like “A Arming Description”
but for arming type D.
Valid entries: up to 128 characters.
Default: empty.
Global Arming Description Like “A Arming Descrip-
tion” but for Global arming.
Valid entries: up to 128 characters.
Default: empty.
Squawk Time On Set squawk (short audible signal)
duration to signal confirmation of arming/disarming or
arming locking (see “USER MANUAL > APPENDIX >
Arming block conditions”), implemented via the com-
mand zone or keyfob:
Ø
one squawk confirms arming/disarming
Ø
two squawks indicate that arming was refused
Squawk Time Off Set the pause between the two
squawks of inhibited arming signalling.
Main Board Wired Siren Squawk This menu shows
the label assigned to output no. 1 (see
Outputs
options
group): select the label of output no. 1 to enable
squawk.
Default: Disabled.
+
The options
Squawk Time On
,
Squawk Time Off
,
and
Main Board Wired Siren Squawk
, apply only to
the sirens connected to output no. 1 (terminals
NC
,
COM
,
NO
,
+N
,
+A
).
Bypass tampers and faults on Zone If enabled, by-
passed zones CANNOT trigger Tamper On Zone
events and System > Zone Fault/Masking .
Enable Auto Arming If this option is enabled the Con-
trol Panel can perform the auto arming set in the Arm-
ing Schedule option group.
Mains Fault Timeout This option will allow you to set
the amount of time that must expire before the Warning
mains failure event occurs.
Valid entries: 0 through 250 minutes, in 1-minute steps
Default: 0 minutes.
e
In order to comply with the EN50131-1, EN50131
and EN50131-3-6 standards, this option should not
be more than 1 minute.
Panel Identifier Code Enter the ID Code assigned to
the control Panel during the Wizard Setup.
+
The Panel ID Code set in BOSS must match with
the one set during the Wizard Setup of the Control
Panel to Downloading/Uploading by means an
USB key.
60 Expandable Hybrid Control Panel
Figure 28 Arming by the Touch Keypad: labels 1 , 2 , 3
and 4 can be customised, as explained in the text; the
corresponding Special arming initial letter will be put in
position
5 ; the description assigned to the arming se-
lected will appear in window 6 , as explained in the text.