Johnson Controls Bentel Security tyco ABS128M50, Руководство по установке

Страница: 64 / 132

Repetition Set the number of times the Control Panel
must repeat the Voice Message.
Valid entries: 1 through 99.
Default: 3.
e
In order to comply with the EN50136-2-4 standards,
the
Repetition option MUST NOT be more then 8.
Audio session timeout Set the two way audio ses-
sion time.
Valid entries: 0 through 240 s (4 minutes), in 1-s steps.
Default: 30 seconds.
Voice Message Transmission Delay Set the pause
between the end of dialling and the Voice Message an-
nouncement.
+
The Voice Message Transmission Delay applies
to the Transmission Delay Enabled option.
Valid entries: 0 through 240 seconds, in 1-second steps.
Default: 30 seconds.
Line check If this option is ENABLED, the Control
Panel will supervise the telephone line.
Default: Disabled.
e
In order to comply with the EN50131-1 and
EN50131-3 standards, this option must be ENABLED
The system will signal “Line down” (i.e. voltage on the
L.E. terminals less than 3 V) by:
Ø
turning ON the
G 7
LED;
Ø
an X (blinking) above the
i
icon;
Ø
generating the Telephone Line Trouble - General
event.
The Control Panel will signal “Line restoral” (voltage on
the
L.E. terminals more than 3 V for the programmed
Pstn Line Restore ) by:
Ø
turning OFF the
G
LED (i.e. unless there are other faults);
Ø
clearing the Trouble signal;
Ø
terminating the Telephone line trouble event.
This option must be disabled when the Control Panel is
not connected to a telephone line, otherwise, the Tele-
phone line trouble event will be signalled persistently.
Tone check If this option is ENABLED, the Control
Panel will check for the dialling tone before dialling. If
the dialling tone is not detected during 30 seconds, the
Control Panel will hang-up and retry.
Don’t Check Incoming Call If the Control Panel
makes a call, and this option is disabled, the control
panel checks if there are incoming calls before dialling
the number. In this case, wait.
Default: Enabled.
+
If the PSTN DoS Generates Fault option in the
group System Options > EN50131/EN50136 is
enabled, this option is disabled and CANNOT be
enabled.
Pstn Line Restoral Time This option will allow you to
setup the time the telephone line voltage must be over 3
V so the Control Panel will signal “Line restoral” (refer to
“Line check”).
Teleservice (IP / GPRS) If disabled, it is NOT possible
to remotely upload and download options or control the
panel status.
Default: Enabled.
Answering machine If this option is ENABLED (fac-
tory setting) the Control Panel will respond to the calls ar-
riving at the PSTN and/or GSM number (see
Answering
Machine Enabled Channels ) after the programmed
Number of Rings (see the Received Call options sub-
group): at this point, if an enabled User PIN is known
(see
DTMF in the Codes and Keys > User options
group) the Control Panel can be managed from the call-
ing telephone (see “TELEPHONE OPERATIONS” in the
User Manual for further information).
+
The Answering Machine function can be En-
abled/Disabled also by the User (refer to “Enable/Dis-
able Answering Machine” in the USER MANUAL).
Answering Machine Enabled Channels Select the
channel used by the Control Panel to answer the phone
calls:
Ø
Only PSTN , the Control Panel will answer ONLY
calls made to its PSTN phone number;
Ø
Only GSM , the Control Panel will answer ONLY calls
made to its GSM phone number;
Ø
PSTN and GSM , the Control Panel will answer calls
made to both its PSTN and its GSM phone number.
Default: Only PSTN.
+
The Present and Enabled options in the GSM op-
tion group must be ENABLED to set this option.
+
If the PSTN DoS Generates Fault option in the
group System Options > EN50131/EN50136 is
enabled, it is NOT possible to select Only PSTN
and PSTN and GSM .
Vocal Guide If this option is enabled (default), a vocal
guide will support the user in the remotely control panel
management via a telephone that support the DTMF
tones (refer to “OPERATING THE SYSTEM FROM A
TELEPHONE” on the User Manual for further informa-
tion). After listening to the welcome message, will be
played the following messages.
Ø
n.159: Welcome. Press pound.
Ø
n.160: Enter code followed by pound.
Ø
n.161: Goodbye. Please hang-up.
Ø
n.162: Alarm call in stand-by. Please hang-up.
Ø
n.163 (Menu 1): Press one for vocal functions.
Ø
n.173 (Sub Menu 1/1): Press one to switch between
talking and audio verification.
Ø
n.174 (Sub Menu 1/2): Press two for two-way call.
Ø
n.175 (Sub Menu 1/4): Press four to reduce audio
verification sensitivity.
64 Expandable Hybrid Control Panel
7 The
G
LED signals several different types of Trouble events. If the signal is due to telephone line trouble, the
Keypad (in View Trouble Mode) will show the Tel.Lin.Failure message.