Johnson Controls Bentel Security tyco ABS128M50, Руководство по установке

Страница: 50 / 132

+
The Fault on Internal Siren Zone supports the
Single End of Line Balance ONLY.
e
In order to comply with the EN50131-1 and
EN50131-3 standards, in the system must be at
least one
Internal Siren Fault Zone.
r
External Siren Fault — Violation of an External Si-
ren Fault Zone — regardless of the status of its Par-
tition — will generate the Fault on External Siren
event.
Default: zone n.
8 (Terminal L4 of the Panel ).
+
The External Siren Fault Zone supports the Sin-
gle End of Line Balance ONLY.
e
In order to comply with the EN50131-1 and
EN50131-3 standards, in the system must be at
least one
External Siren Fault Zone.
Roller Blind-Enabled This option must be enabled on
the Zones used for Roller blind contacts (This is valid
only for main board zones). If you enable this option you
must set the
Roller Blind-Window and Pulses-Num-
ber , that determine the zone violation.
Roller Blind-Window Set the time available to count
the set Pulses-Number so the zone will trigger an
alarm), as per the following example.
E.g. a zone with a
Pulses-Number of 4 and a Roller
Blind-Window of 2 minutes, will signal violation when
its contact generates 4 pulses within 2 minutes.
Vibration-Enabled This option must be enabled on
the Zones used for Vibration detectors (This is valid
only for main board zones). If you enable this option you
must
set the options Vibration-Sensitivity and
Pulses-Number , that determine the zone violation, as
per the following example.
Vibration-Sensitivity If the Pulses-Number is 0 or 1 ,
the zone alarm is triggered with a single pulse with a du-
ration equal to that of the
Vibration-Sensitivity : from 1,
very sensitive, to 20, insensitive.
If the
Pulses-Number exceeds 1 , the zone alarm is
triggered ALSO when the Pulses-Number set is
counted: the pulses must be at least 250
m
s long.
E.g. a zone with the Vibration-Sensitivity of 10 and
Pulses-Number of 5 will generate an alarm when:
Ø
it detects a single pulse that exceeds the Vibra-
tion-Sensitivity of 10 (the zone will be open for at
least 50 ms);
Ø
it detects 5 pulses at least 250
m
s long.
Cycles This option determines the number of times the
Zone will be able to trigger the Zone Alarm event.
Valid entries: 0 through 255:
Ø
If 0 is set up, the Zone will be unable to trigger Zone
Alarm events;
Ø
if any number other than 0 is set up, the Zone will be
able to trigger the corresponding number of Alarm
events;
Ø
if 255 is set up, the Zone will be able to trigger an un-
limited number of Zone Alarm events.
The Zone Alarm Cycle counter will reset when:
Ø
one of the Partitions of the Zone changes status;
Ø
one of the Partitions of the Zone Resets;
Ø
one of the Partitions of the Zone exits Block Alarm
status;
Ø
the programming session ends (i.e. when you exit the
Installer Menu or complete downloading via the PC);
Ø
the Zone is Unbypassed.
+
A Zone that signals a persistent Alarm condition (e.g.
due to Trouble conditions) will generate one Alarm
cycle ONLY. It will be unable to generate further cy-
cles until the Alarm counter has been cleared.
e
In order to comply with the EN50131-1 and
EN50131-3 standards, the Hold-up Zone’s Cycles
must be 255.
Pulses-Number Set the number of pulses required
(the number of times the zone is violated) before the
zone generate an alarm. Depending on the zone type it
has different meanings and value ranges.
Ø
For zone with Roller Blind option Enabled it deter-
mines the number of fast pulses (greater than 600
m
s) the zone will allow before signalling the alarm (1
through 7).
Ø
For zone with Vibration option Enabled it deter-
mines whether the zone alarm is triggered by a pulse
with a length equal to the
Vibration-Sensitivity set
(0 or 1) or ALSO when the Pulses-Number set is
counted.
Ø
For all other type of zone it determines the number of
pulses required (pulses greater than 300 ms) before
the zone trigger an alarm (value range 1 through 3).
Pulses-Window Set the time to count the Pulses-Num-
ber programmed.
Valid values: Disabled, and from 4 to 64 s in steps of 4 s.
Default: 4 seconds.
Alarm if single pulse longer than time window If
this option is disabled (default), the zone goes into
alarm when it counts the programmed
Pulses before
the programmed Window expires.
If this option is enabled, the zone goes into alarm even
when it detect a single pulse longer than the pro-
grammed
Window .
Attributes-Bypassable Zones with this attribute can
be Bypassed.
e
In compliance with the EN50131-1 and EN50131-3
standards, a bypassed zone is defined
Isolated
Zone , when it is manually bypassed by the user;
Inhibited Zone , when it is automatically bypassed
by the panel (see “Autobypassable” and
“Autobypass with Reset Unbypass”).
Attributes-Chime Violation of a Zone with this attrib-
ute — during Disarmed status of its Partition — will gen-
erate the
Chime on partition no. event, and an audible
50 Expandable Hybrid Control Panel