Johnson Controls Bentel Security tyco ABS128M50, Руководство по установке

Страница: 19 / 132

MOUNTING THE COMPONENTS
Mounting the Metal Box
Please read the following instructions, to get an overall
view of the steps involved in the control panel mounting
with the
ABS-M Metal Box: refer to Figure 4 and Figure
2 on page 16.
Installing ABSOLUTA Plus Main Board
1. Insert the five reverse locking supports into the
holes
44 on the backplate.
2. Place the Main Board on the supports, then press it
down until blocks in its position.
3. Secure the Earth wire (Yellow-Green) eyelet to the
hole
46 on the backplate, by means the screw
M3x8 and washer.
4. Connect the other end of the earth wire (Yel-
low-Green)
28 to terminal
-
on the ABSOLUTA
Plus main board.
!
The Main Board must be earthed in order to pro-
tect it from electrical surges from the Telephone
Line, and comply with Safety Regulations.
Installing the Power Supply You can install the
Switching Power Supply BAW35T12, BAW50T12 or
BAW75T12 into the Metal Box, as shown in Figure 2 on
page 16 (part nr.
31 ).
5. Cut the battery cables on the power supply.
+
The backup battery must be connected to the con-
nector
13 on the Main Board. It can NOT be con-
nected directly to power supply.
6. BAW50T12 / BAW75T12 : slide the Power Supply
tab under the hook 54 .
BAW35T12 : screw a M3X8 screw on the hole 53a,
loosely, then slide the Power Supply tab in the
screw and tighten it.
7. Secure the BAW75T12 to the hole 51 , the
BAW50T12 and the BAW35T12 to the hole 53 , by
means the washer and screw (M3x8).
8. Insert the Power Supply plug into the connector 12
on the Main Board.
9. Secure the exceeding wires to the anchor 48 on the
backplate.
Installing the Tamper Switch You can install the
MAXIASNC switch (accessory item required to comply with
the EN50131-1 and EN50131-3 standards) to detect the box
opening, as shown in Figure 2 on page 16 (part nr.
25 ).
10. Secure the MAXIASNC switch to its location using
the two hexagonal nuts.
11. Connect the wire to the connector 3 ( T ) on the Main
Board.
Installing the Wall-Tamper Switch You can install the
MAXIASNC switch (accessory item required to comply with
the EN50131-1 and EN50131-3 standards) to detect the box
removal, as shown in Figure 2 on page 16 (part nr.
37 ).
12. Place the Wall-Tamper Bracket 24 into the opening
41 on the backplate.
13. Secure the MAXIASNC switch to its location using
the two hexagonal nuts.
14. Connect the wire to the connector 4 ( S ) on the Main
Board.
Installing the Input/Output Expander Module You
can install up to two Input/Output Expander Modules
M-IN/OUT into the Metal Box, as shown in Figure 2 on
page 16 (parts nr. 34 and 38 ).
15. Insert four reverse locking supports into the holes 58
and/or into the holes 56 on the backplate, depending
on if you are installing one and/or two Modules.
16. Place the Module PCB on the supports, then press
it down until blocks in its position.
17. Disable the tamper and wall-tamper contacts by in-
serting (closing) the jumper on the Input/Output Ex-
pander Module (
TAMP DIS ).
Marking Label Once you have assembled the compo-
nents, specify on the data label (which is located on the
outer right side of the box) the type of Control Panel that
you have constructed.
18. Using an indelible pen, tick the relevant box on the
Marking Label according to the following table.
ABS-M Power Supplies
Main Boards BAW35T12 BAW50T12 BAW75T12
ABS-18 ABS18M35 N/A N/A
ABS-48 ABS48M35 ABS48M50 ABS48M75
ABS-128 N/A ABS128M50 ABS128M75
ABSOLUTA Plus MOUNTING THE COMPONENTS 19