IEI Technology KINO-945GSE3 Скачать руководство пользователя страница 99

Страница: 99 / 178

KINO-945GSE3 User Manual

Page 85

IRQ10

Serial port 3 IRQ address is 10.

Select RS232 or RS485/RS422 [RS/232]

Use the

Select RS232 or RS485/RS422

option to select the Serial Port 3 signaling mode.

RS232

EFAULT

Serial Port 3 signaling mode is RS-232

RS422/RS485

Serial Port 3 signaling mode is RS-422/RS485

Serial Port4 Address [2E8]

Use the

Serial Port4 Address

option to select the Serial Port 4 base address.

Disabled

No base address is assigned to Serial Port 4

3F8

Serial Port 4 I/O port address is 3F8.

2F8

Serial Port 4 I/O port address is 2F8

3E8

Serial Port 4 I/O port address is 3E8.

2E8 D

EFAULT

Serial Port 4 I/O port address is 2E8.

3E0

Serial Port 4 I/O port address is 3E0.

2E0

Serial Port 4 I/O port address is 2E0.

Serial Port4 IRQ [IRQ3]

Use the

Serial Port4 IRQ

option to select the interrupt address for serial port 4.

IRQ3 D

EFAULT

Serial port 4 IRQ address is 3.

IRQ4

Serial port 4 IRQ address is 4.

IRQ10

Serial port 4 IRQ address is 10.

Serial Port5 Address [3E0]

Use the

Serial Port5 Address

option to select the Serial Port 5 base address.

Disabled

No base address is assigned to Serial Port 5

Содержание KINO-945GSE3



















































































































































































Результаты поиска

Содержание KINO-945GSE3

Отзывы:

IEI Technology KINO-945GSE3, Руководство пользователя, Страница: 99 / 178

Результаты поиска

Содержание KINO-945GSE3

Отзывы: