IEI Technology KINO-945GSE3 Скачать руководство пользователя страница 75

Страница: 75 / 178

KINO-945GSE3 User Manual

Page 61

4.6.1 DVI Display Device Connection

The KINO-945GSE3 has a single female DVI-D connector on the external peripheral

interface panel. The DVI-D connector is connected to a digital display device. To connect

a digital display device to the KINO-945GSE3, please follow the instructions below.

Step 5:

Locate the DVI-D connector

. The location of the DVI-D connector is shown in

another chapter.

Step 6:

Align the DVI-D connector

. Align the male DVI-D connector on the digital

display device cable with the female DVI-D connector on the external peripheral

interface.

Step 7:

Insert the DVI-D connector

Once the connectors are properly aligned with the

male connector, insert the male connector from the digital display device into the

female connector on the KINO-945GSE3. See Figure 4-15.

Figure 4-15: DVI Connector

Step 8:

Secure the connector.

Secure the DVI-D connector from the digital display

device to the external interface by tightening the two retention screws on either

side of the connector.

Step 0:

Содержание KINO-945GSE3



















































































































































































Результаты поиска

Содержание KINO-945GSE3

Отзывы:

IEI Technology KINO-945GSE3, Руководство пользователя, Страница: 75 / 178

Результаты поиска

Содержание KINO-945GSE3

Отзывы: