IEI Technology KINO-945GSE3 Скачать руководство пользователя страница 84

Страница: 84 / 178

KINO-945GSE3 User Manual

Page 70

Key

Function

F2 /F3 key

Change color from total 16 colors. F2 to select color

forward.

F10 key

Save all the CMOS changes, only for Main Menu

Table 5-1: BIOS Navigation Keys

5.1.3 Getting Help

When

is pressed a small help window describing the appropriate keys to use and the

possible selections for the highlighted item appears. To exit the Help Window press

the

key again.

5.1.4 Unable to Reboot After Configuration Changes

If the computer cannot boot after changes to the system configuration is made, CMOS

defaults. Use the jumper described in Chapter

5.1.5 BIOS Menu Bar

The

menu bar

on top of the BIOS screen has the following main items:

Main – Changes the basic system configuration.

Advanced – Changes the advanced system settings.

PCIPnP – Changes the advanced PCI/PnP Settings

Boot – Changes the system boot configuration.

Security – Sets User and Supervisor Passwords.

Chipset – Changes the chipset settings.

Power – Changes power management settings.

Exit – Selects exit options and loads default settings

The following sections completely describe the configuration options found in the menu

items at the top of the BIOS screen and listed above.

Содержание KINO-945GSE3



















































































































































































Результаты поиска

Содержание KINO-945GSE3

Отзывы:

IEI Technology KINO-945GSE3, Руководство пользователя, Страница: 84 / 178

Результаты поиска

Содержание KINO-945GSE3

Отзывы: