IEI Technology KINO-945GSE3 Скачать руководство пользователя страница 93

Страница: 93 / 178

KINO-945GSE3 User Manual

Page 79

Block (Multi Sector Transfer) [Auto]

Use the

Block (Multi Sector Transfer)

to disable or enable BIOS to auto detect if the

device supports multi-sector transfers.

Disabled

BIOS is prevented from using Multi-Sector Transfer on the

specified channel. The data to and from the device occurs

one sector at a time.

Auto D

EFAULT

BIOS auto detects Multi-Sector Transfer support on the

drive on the specified channel. If supported the data

transfer to and from the device occurs multiple sectors at

a time.

PIO Mode [Auto]

Use the

PIO Mode

option to select the IDE PIO (Programmable I/O) mode program timing

cycles between the IDE drive and the programmable IDE controller. As the PIO mode

increases, the cycle time decreases.

Auto D

EFAULT

BIOS auto detects the PIO mode. Use this value if the IDE disk

drive support cannot be determined.

PIO mode 0 selected with a maximum transfer rate of 3.3 MB/s

PIO mode 1 selected with a maximum transfer rate of 5.2 MB/s

PIO mode 2 selected with a maximum transfer rate of 8.3 MB/s

PIO mode 3 selected with a maximum transfer rate of 11.1 MB/s

PIO mode 4 selected with a maximum transfer rate of 16.6 MB/s

(This setting generally works with all hard disk drives

manufactured after 1999. For other disk drives, such as IDE

CD-ROM drives, check the specifications of the drive.)

DMA Mode [Auto]

Use the

DMA Mode

BIOS selection to adjust the DMA mode options.

Содержание KINO-945GSE3



















































































































































































Результаты поиска

Содержание KINO-945GSE3

Отзывы:

IEI Technology KINO-945GSE3, Руководство пользователя, Страница: 93 / 178

Результаты поиска

Содержание KINO-945GSE3

Отзывы: