IEI Technology KINO-945GSE3 Скачать руководство пользователя страница 109

Страница: 109 / 178

KINO-945GSE3 User Manual

Page 95

Remote Access [Disabled]

Use the

Remote Access

option to enable or disable access to the remote functionalities

of the system.

Disabled D

EFAULT

Remote access is disabled.

Enabled

Remote access configuration options shown below

appear:

Serial Port Number

Serial Port Mode

Flow

Control

Redirection after BIOS POST

Terminal

Type

VT-UTF8 Combo Key Support

These configuration options are discussed below.

Serial Port Number [COM1]

Use the

Serial Port Number

option to select the serial port used for remote access.

COM1 D

EFAULT

System is remotely accessed through COM1

COM2

System is remotely accessed through COM2

NOTE

: Make sure the selected COM port is enabled through the Super I/O configuration

menu.

Base Address, IRQ [2F8h,3]

The

Base Address, IRQ

option cannot be configured and only shows the interrupt

address of the serial port listed above.

Serial Port Mode [115200 8,n,1]

Use the

Serial Port Mode

option to select baud rate through which the console redirection

is made. The following configuration options are available

Содержание KINO-945GSE3



















































































































































































Результаты поиска

Содержание KINO-945GSE3

Отзывы:

IEI Technology KINO-945GSE3, Руководство пользователя, Страница: 109 / 178

Результаты поиска

Содержание KINO-945GSE3

Отзывы: