IEI Technology KINO-945GSE3 Скачать руководство пользователя страница 110

Страница: 110 / 178

KINO-945GSE3 User Manual

Page 96

115200

8,n,1

EFAULT

57600

8,n,1

38400

8,n,1

19200

8,n,1

09600

8,n,1

NOTE:

Identical baud rate setting musts be set on the host (a management

computer running a terminal software) and the slave

Redirection After BIOS POST [Always]

Use the

Redirection After BIOS POST

option to specify when console redirection should

occur.

Disabled

The console is not redirected after POST

Boot Loader

Redirection is active during POST and during Boot

Loader

Always D

EFAULT

Redirection is always active (Some OSes may not

work if set to Always)

Terminal Type [ANSI]

Use the

Terminal Type

BIOS option to specify the remote terminal type.

ANSI D

EFAULT

The target terminal type is ANSI

VT100

The target terminal type is VT100

VT-UTF8

The target terminal type is VT-UTF8

VT-UTF8 Combo Key Support [Disabled]

Use the

VT-UFT8 Combo Key Support

option to enable additional keys that are not

provided by VT100 for the PC 101 keyboard.

Содержание KINO-945GSE3



















































































































































































Результаты поиска

Содержание KINO-945GSE3

Отзывы:

IEI Technology KINO-945GSE3, Руководство пользователя, Страница: 110 / 178

Результаты поиска

Содержание KINO-945GSE3

Отзывы: