IEI Technology KINO-945GSE3 Скачать руководство пользователя страница 97

Страница: 97 / 178

KINO-945GSE3 User Manual

Page 83

Serial Port1 IRQ [IRQ4]

Use the

Serial Port1 IRQ

option to select the interrupt address for serial port 1.

IRQ3

Serial port 1 IRQ address is 3.

IRQ4 D

EFAULT

Serial port 1 IRQ address is 4.

IRQ10

Serial port 1 IRQ address is 10.

Serial Port2 Address [2F8]

Use the

Serial Port2 Address

option to select the Serial Port 2 base address.

Disabled

No base address is assigned to Serial Port 2

3F8

Serial Port 2 I/O port address is 3F8.

2F8 D

EFAULT

Serial Port 2 I/O port address is 2F8

3E8

Serial Port 2 I/O port address is 3E8.

2E8

Serial Port 2 I/O port address is 2E8.

3E0

Serial Port 2 I/O port address is 3E0.

2E0

Serial Port 2 I/O port address is 2E0.

Serial Port2 IRQ [IRQ3]

Use the

Serial Port2 IRQ

option to select the interrupt address for serial port 2.

IRQ3 D

EFAULT

Serial port 2 IRQ address is 3.

IRQ4

Serial port 2 IRQ address is 4.

IRQ10

Serial port 2 IRQ address is 10.

Serial Port2 Address [2F8/IRQ3]

Use the

Serial Port2 Address

option to select the Serial Port 2 base address.

Disabled

No base address is assigned to Serial Port 2

Содержание KINO-945GSE3



















































































































































































Результаты поиска

Содержание KINO-945GSE3

Отзывы:

IEI Technology KINO-945GSE3, Руководство пользователя, Страница: 97 / 178

Результаты поиска

Содержание KINO-945GSE3

Отзывы: