IEI Technology KINO-945GSE3 Скачать руководство пользователя страница 92

Страница: 92 / 178

KINO-945GSE3 User Manual

Page 78

32Bit Data Transfer: Enables 32-bit data transfer.

Type [Auto]

Use the

Type

BIOS option select the type of device the AMIBIOS attempts to boot from

after the Power-On Self-Test (POST) is complete.

Not Installed

BIOS is prevented from searching for an IDE disk

drive on the specified channel.

Auto D

EFAULT

The BIOS auto detects the IDE disk drive type

attached to the specified channel. This setting should

be used if an IDE hard disk drive is attached to the

specified channel.

CD/DVD

The CD/DVD option specifies that an IDE CD-ROM

drive is attached to the specified IDE channel. The

BIOS does not attempt to search for other types of

IDE disk drives on the specified channel.

ARMD

This option specifies an ATAPI Removable Media

Device. These include, but are not limited to:

ZIP

LS-120

LBA/Large Mode [Auto]

Use the

LBA/Large Mode

option to disable or enable BIOS to auto detects LBA (Logical

Block Addressing). LBA is a method of addressing data on a disk drive. In LBA mode, the

maximum drive capacity is 137 GB.

Disabled

BIOS is prevented from using the LBA mode control on

the specified channel.

Auto D

EFAULT

BIOS auto detects the LBA mode control on the specified

channel.

Содержание KINO-945GSE3



















































































































































































Результаты поиска

Содержание KINO-945GSE3

Отзывы:

IEI Technology KINO-945GSE3, Руководство пользователя, Страница: 92 / 178

Результаты поиска

Содержание KINO-945GSE3

Отзывы: