IEI Technology KINO-945GSE3 Скачать руководство пользователя страница 107

Страница: 107 / 178

KINO-945GSE3 User Manual

Page 93

Resume on Keyboard/Mouse [Disabled]

Use the

Resume on Keyboard/Mouse

BIOS option to enable activity on either the

keyboard or mouse to rouse the system from a suspend or standby state. That is, the

system is roused when the mouse is moved or a button on the keyboard is pressed.

Disabled D

EFAULT

Wake event not generated by activity on the

keyboard or mouse

Resume On

KeyBoard

Wake event generated by activity on the keyboard

Resume On

Mouse

Wake event generated by activity on the mouse

Enabled

Wake event generated by activity on the keyboard or

mouse

Resume on Ring [Disabled]

Use the

Resume on Ring

BIOS option to enable activity on the RI (ring in) modem line to

rouse the system from a suspend or standby state. That is, the system will be roused by

an incoming call on a modem.

Disabled D

EFAULT

Wake event not generated by an incoming call

Enabled

Wake event generated by an incoming call

Resume On RTC Alarm [Disabled]

Use the

Resume On RTC Alarm

option to specify the time the system should be roused

from a suspended state.

Disabled D

EFAULT

The real time clock (RTC) cannot generate a wake

event

Содержание KINO-945GSE3



















































































































































































Результаты поиска

Содержание KINO-945GSE3

Отзывы:

IEI Technology KINO-945GSE3, Руководство пользователя, Страница: 107 / 178

Результаты поиска

Содержание KINO-945GSE3

Отзывы: