IEI Technology KINO-945GSE3 Скачать руководство пользователя страница 23

Страница: 23 / 178

KINO-945GSE3 User Manual

Page 9

2.1 Unpacking Checklist

WARNING!

Static electricity can destroy certain electronics. Make sure to follow the

ESD precautions to prevent damage to the product, and injury to the

user.

Make sure to adhere to the following guidelines:

Wear an anti-static wristband

: Wearing an anti-static wristband can prevent

electrostatic discharge.

Self-grounding

: Touch a grounded conductor every few minutes to discharge

any excess static buildup.

Use an anti-static pad

: When configuring any circuit board, place it on an

anti-static mat.

Only handle the edges of the PCB

: Don't touch the surface of the

motherboard. Hold the motherboard by the edges when handling.

2.2 Unpacking Precautions

When the KINO-945GSE3 is unpacked, please do the following:

Follow the antistatic guidelines above.

Make sure the packing box is facing upwards when opening.

Make sure all the packing list items are present.

Содержание KINO-945GSE3



















































































































































































Результаты поиска

Содержание KINO-945GSE3

Отзывы:

IEI Technology KINO-945GSE3, Руководство пользователя, Страница: 23 / 178

Результаты поиска

Содержание KINO-945GSE3

Отзывы: