IEI Technology KINO-945GSE3 Скачать руководство пользователя страница 112

Страница: 112 / 178

KINO-945GSE3 User Manual

Page 98

USB Function [Enabled]

Use the

USB Function

BIOS option to enable or disable USB function support.

Disabled

USB function support disabled

Enabled D

EFAULT

USB function support enabled

USB 2.0 Controller [Enabled]

Use the

USB 2.0 Controller

BIOS option to enable or disable the USB 2.0 controller

Disabled

USB 2.0 controller disabled

Enabled D

EFAULT

USB 2.0 controller enabled

Legacy USB Support [Enabled]

Use the

Legacy USB Support

BIOS option to enable USB mouse and USB keyboard

support.

Normally if this option is not enabled, any attached USB mouse or USB keyboard does not

become available until a USB compatible operating system is fully booted with all USB

drivers loaded. When this option is enabled, any attached USB mouse or USB keyboard

can control the system even when there is no USB driver loaded onto the system.

Disabled

Legacy USB support disabled

Enabled D

EFAULT

Legacy USB support enabled

Auto

Legacy USB support disabled if no USB devices are

connected

USB2.0 Controller Mode [HiSpeed]

Use the

USB2.0 Controller Mode

option to set the speed of the USB2.0 controller.

FullSpeed

The controller is capable of operating at 12 Mb/s

HiSpeed D

EFAULT

The controller is capable of operating at 480 Mb/s

Содержание KINO-945GSE3



















































































































































































Результаты поиска

Содержание KINO-945GSE3

Отзывы:

IEI Technology KINO-945GSE3, Руководство пользователя, Страница: 112 / 178

Результаты поиска

Содержание KINO-945GSE3

Отзывы: