IEI Technology KINO-945GSE3 Скачать руководство пользователя страница 123

Страница: 123 / 178

KINO-945GSE3 User Manual

Page 109

The boot sequence from the available devices is selected. If the “

1st Drive

” option is

selected a list of available CD/DVD drives is shown. Select the first CD/DVD drive the

system boots from. If the “

1st Drive

” is not used for booting this option may be disabled.

BIOS SETUP UTILITY

Main

Advanced

PCIPNP

Boot

Security

Chipset

Power

Exit

Hard Disk Drives

⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯

> 1st Drive

[CD/DVD 1]

> 2nd Drive

[CD/DVD 2]

> 3rd Drive

[CD/DVD 3]

Specifies the boot
sequence from the
available devices.

Select

Screen

↑

↓

Select

Item

Enter Go to SubScreen
F1 General

Help

F10

Save and Exit

ESC Exit

BIOS Menu 20: CD/DVD Drives

5.6 Security

Use the

Security

menu (

BIOS Menu 21

) to set system and user passwords.

BIOS SETUP UTILITY

Main

Advanced

PCIPNP

Boot

Security

Chipset

Power

Exit

Security Settings

⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯

Supervisor Password :Not Installed
User Password :Not Installed

Change Supervisor Password
Change User Password

Select

Screen

↑

↓

Select

Item

Enter Go to SubScreen
F1 General

Help

F10

Save and Exit

ESC Exit

BIOS Menu 21: Security

Содержание KINO-945GSE3



















































































































































































Результаты поиска

Содержание KINO-945GSE3

Отзывы:

IEI Technology KINO-945GSE3, Руководство пользователя, Страница: 123 / 178

Результаты поиска

Содержание KINO-945GSE3

Отзывы: