IEI Technology KINO-945GSE3 Скачать руководство пользователя страница 67

Страница: 67 / 178

KINO-945GSE3 User Manual

Page 53

Figure 4-7: COM2 Function Select Jumper
Location

4.3.6 LVDS1 Panel Resolution Jumper

Jumper Label:

J_LCD_TYPE1

Jumper Type:

8-pin header

Jumper Settings:

See

Table 4-7

Jumper Location:

See

Figure 4-8

The LVDS1 Panel Resolution jumper allows the resolution of the LVDS screens

connected to the LVDS1 connector to be configured. The LVDS1 Panel Resolution jumper

settings are shown in

Table 4-7

DESCRIPTION (LVDS1)

Pin 1-2 Pin 3-4 Pin 5-6 Pin 7-8 Resolution

OPEN OPEN OPEN SHORT 640 x 480 (18-bit)

SHORT

OPEN OPEN OPEN 800 x 480 (18-bit)

OPEN SHORT OPEN OPEN 800 x 600 (18-bit) Default

SHORT SHORT OPEN OPEN 1024 x 768 (18-bit)

OPEN OPEN SHORT OPEN 1280 x 1024 (36-bit)

SHORT OPEN SHORT OPEN 1400 x 1050 (36-bit)

OPEN SHORT SHORT OPEN 1440 x 900 (36-bit)

SHORT SHORT SHORT OPEN 1600 x 1200 (36-bit)

Table 4-7: LVDS Panel Resolution Jumper Settings

The LVDS Panel Resolution jumper location is shown in

Figure 4-8

Содержание KINO-945GSE3



















































































































































































Результаты поиска

Содержание KINO-945GSE3

Отзывы:

IEI Technology KINO-945GSE3, Руководство пользователя, Страница: 67 / 178

Результаты поиска

Содержание KINO-945GSE3

Отзывы: