IEI Technology KINO-945GSE3 Скачать руководство пользователя страница 106

Страница: 106 / 178

KINO-945GSE3 User Manual

Page 92

BIOS SETUP UTILITY

Main

Advanced

PCIPNP

Boot

Security

Chipset

Power

Exit

APM Configuration

⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯

Restore on AC Power Loss

[Power On]

Power Button Mode

[On/Off]

Advanced Resume Event Controls

Resume On Ring

[Disabled]

Resume on PS2 Keyboard/Mouse

[Disabled]

Resume on PCI Express Wake

[Disabled]

Resume on RTC Alarm

[Disabled]

Go into On/Off, or
Suspend when Power
button is pressed

Select

Screen

↑

↓

Select

Item

Enter Go to SubScreen
F1 General

Help

F10

Save and Exit

ESC Exit

BIOS Menu 10: APM Configuration

Power Button Mode [On/Off]

Use the

Power Button Mode

BIOS to specify how the power button functions.

On/Off D

EFAULT

When the power button is pressed the system is either

turned on or off

Suspend

When the power button is pressed the system goes into

suspend mode

Restore on AC Power Loss [Power On]

Use the

Restore on AC Power Loss

BIOS option to specify what state the system

returns to if there is a sudden loss of power to the system.

Power Off

The system remains turned off

Power On

EFAULT

The system turns on

Last State

The system returns to its previous state. If it was on, it

turns itself on. If it was off, it remains off.

Содержание KINO-945GSE3



















































































































































































Результаты поиска

Содержание KINO-945GSE3

Отзывы:

IEI Technology KINO-945GSE3, Руководство пользователя, Страница: 106 / 178

Результаты поиска

Содержание KINO-945GSE3

Отзывы: