IEI Technology KINO-945GSE3 Скачать руководство пользователя страница 152

Страница: 152 / 178

KINO-945GSE3 User Manual

Page 138

NOTE:

Please reserve enough space for partition 3 for saving recovery

images.

Figure B-19: Partitions for Linux

Step 3:

Create a recovery partition

. Insert the recovery CD into the optical disk drive.

Step 1

Step 3

described

Section B.2.2

. Then type the following

commands (marked in red) to create a partition for recovery images.

system32>

diskpart

DISKPART>

list vol

DISKPART>

sel disk 0

DISKPART>

create part pri size=

___

DISKPART>

assign letter=N

DISKPART>

exit

system32>

format N: /fs:ntfs /q /v:Recovery /y

system32>

exit

Step 4:

Build-up recovery partition

. Press any key to boot from the recovery CD. It will

take a while to launch the recovery tool. Please be patient. When the recovery

tool setup menu appears, type <

> and press <Enter> (

Figure B-20

). The

Symantec Ghost window appears and starts configuring the system to build-up a

Содержание KINO-945GSE3



















































































































































































Результаты поиска

Содержание KINO-945GSE3

Отзывы:

IEI Technology KINO-945GSE3, Руководство пользователя, Страница: 152 / 178

Результаты поиска

Содержание KINO-945GSE3

Отзывы: