IEI Technology KINO-945GSE3 Скачать руководство пользователя страница 160

Страница: 160 / 178

KINO-945GSE3 User Manual

Page 146

B.5 Other Information

B.5.1 Using AHCI Mode or ALi M5283 / VIA VT6421A Controller

When the system uses AHCI mode or some specific SATA controllers such as ALi M5283

or VIA VT6421A, the SATA RAID/AHCI driver must be installed before using one key

recovery. Please follow the steps below to install the SATA RAID/AHCI driver.

Step 1:

Copy the SATA RAID/AHCI driver to a floppy disk and insert the floppy disk into

a USB floppy disk drive. The SATA RAID/AHCI driver must be especially

designed for the on-board SATA controller.

Step 2:

Connect the USB floppy disk drive to the system.

Step 3:

Insert the One Key Recovery CD into the system and boot the system from the

CD.

Step 4:

When launching the recovery tool, press <

Содержание KINO-945GSE3



















































































































































































Результаты поиска

Содержание KINO-945GSE3

Отзывы:

IEI Technology KINO-945GSE3, Руководство пользователя, Страница: 160 / 178

Результаты поиска

Содержание KINO-945GSE3

Отзывы: