IEI Technology KINO-945GSE3 Скачать руководство пользователя страница 118

Страница: 118 / 178

KINO-945GSE3 User Manual

Page 104

Quick Boot [Enabled]

Use the

Quick Boot

BIOS option to make the computer speed up the boot process.

Disabled

No POST procedures are skipped

Enabled D

EFAULT

Some POST procedures are skipped to decrease

the system boot time

Boot From LAN Support [Disabled]

Use the

BOOT From LAN Support

option to enable the system to be booted from a

remote system.

Disabled D

EFAULT

Cannot be booted from a remote system through the

LAN

Enabled D

EFAULT

Can be booted from a remote system through the

LAN

Quiet Boot [Disabled]

Use the

Quiet Boot

BIOS option to select the screen display when the system boots.

Disabled D

EFAULT

Normal POST messages displayed

Enabled

OEM Logo displayed instead of POST messages

AddOn ROM Display Mode [Force BIOS]

Use the

AddOn ROM Display Mode

option to allow add-on ROM (read-only memory)

messages to be displayed.

Force BIOS

EFAULT

The system forces third party BIOS to display

during system boot.

Keep Current

The system displays normal information during

system boot.

Содержание KINO-945GSE3



















































































































































































Результаты поиска

Содержание KINO-945GSE3

Отзывы:

IEI Technology KINO-945GSE3, Руководство пользователя, Страница: 118 / 178

Результаты поиска

Содержание KINO-945GSE3

Отзывы: