IEI Technology KINO-945GSE3 Скачать руководство пользователя страница 130

Страница: 130 / 178

KINO-945GSE3 User Manual

Page 116

BIOS SETUP UTILITY

Main

Advanced

PCIPNP

Boot

Security

Chipset

Power

Exit

Exit Options

⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯

Save Changes and Exit
Discard Changes and Exit
Discard Changes

Load Optimal Defaults
Load Failsafe Defaults

Exit system setup after
saving the changes.

F10 key can be used for
this operation

Select

Screen

↑

↓

Select

Item

Enter Go to SubScreen
F1 General

Help

F10

Save and Exit

ESC Exit

BIOS Menu 25: Exit

Save Changes and Exit

Use the

Save Changes and Exit

option to save the changes made to the BIOS options

and to exit the BIOS configuration setup program.

Discard Changes and Exit

Use the

Discard Changes and Exit

option to exit the BIOS configuration setup program

without saving the changes made to the system.

Discard Changes

Use the

Discard Changes

option to discard the changes and remain in the BIOS

configuration setup program.

Load Optimal Defaults

Use the

Load Optimal Defaults

option to load the optimal default values for each of the

parameters on the Setup menus.

F9 key can be used for this operation.

Load Failsafe Defaults

Use the

Load Failsafe Defaults

option to load failsafe default values for each of the

parameters on the Setup menus.

F8 key can be used for this operation.

Содержание KINO-945GSE3



















































































































































































Результаты поиска

Содержание KINO-945GSE3

Отзывы:

IEI Technology KINO-945GSE3, Руководство пользователя, Страница: 130 / 178

Результаты поиска

Содержание KINO-945GSE3

Отзывы: