IEI Technology KINO-945GSE3 Скачать руководство пользователя страница 94

Страница: 94 / 178

KINO-945GSE3 User Manual

Page 80

Auto D

EFAULT

BIOS auto detects the DMA mode. Use this value if the IDE

disk drive support cannot be determined.

SWDMA0

Single Word DMA mode 0 selected with a maximum data

transfer rate of 2.1 MB/s

SWDMA1

Single Word DMA mode 1 selected with a maximum data

transfer rate of 4.2 MB/s

SWDMA2

Single Word DMA mode 2 selected with a maximum data

transfer rate of 8.3 MB/s

MWDMA0

Multi Word DMA mode 0 selected with a maximum data

transfer rate of 4.2 MB/s

MWDMA1

Multi Word DMA mode 1 selected with a maximum data

transfer rate of 13.3 MB/s

MWDMA2

Multi Word DMA mode 2 selected with a maximum data

transfer rate of 16.6 MB/s

UDMA0

Ultra DMA mode 0 selected with a maximum data transfer

rate of 16.6 MB/s

UDMA1

Ultra DMA mode 1 selected with a maximum data transfer

rate of 25 MB/s

UDMA2

Ultra DMA mode 2 selected with a maximum data transfer

rate of 33.3 MB/s

UDMA3

Ultra DMA mode 3 selected with a maximum data transfer

rate of 44 MB/s (To use this mode, it is required that an

80-conductor ATA cable is used.)

UDMA4

Ultra DMA mode 4 selected with a maximum data transfer

rate of 66.6 MB/s (To use this mode, it is required that an

80-conductor ATA cable is used.)

UDMA5

Ultra DMA mode 5 selected with a maximum data transfer

rate of 99.9 MB/s (To use this mode, it is required that an

80-conductor ATA cable is used.)

Содержание KINO-945GSE3



















































































































































































Результаты поиска

Содержание KINO-945GSE3

Отзывы:

IEI Technology KINO-945GSE3, Руководство пользователя, Страница: 94 / 178

Результаты поиска

Содержание KINO-945GSE3

Отзывы: