IEI Technology KINO-945GSE3 Скачать руководство пользователя страница 126

Страница: 126 / 178

KINO-945GSE3 User Manual

Page 112

Memory Hole [Disabled]

Use the

Memory Hole

option to reserve memory space between 15 MB and 16 MB for

ISA expansion cards that require a specified area of memory to work properly. If an older

ISA expansion card is used, please refer to the documentation that came with the card to

see if it is necessary to reserve the space.

Disabled D

EFAULT

Memory is not reserved for ISA expansion cards

15 MB–16 MB

Between 15 MB and 16 MB of memory is reserved

for ISA expansion cards

Internal Graphics Mode Select [Enable, 8 MB]

Use the

Internal Graphic Mode Select

option to specify the amount of system memory

that can be used by the internal graphics device.

Disable

Enable, 1 MB

1 MB of memory used by internal graphics device

Enable, 8 MB

EFAULT

8 MB of memory used by internal graphics device

DVMT Mode Select [DVMT Mode]

Use the

DVMT Mode Select

option to select the Intel

Dynamic Video Memory Technology

(DVMT) operating mode.

Fixed Mode

A fixed portion of graphics memory is reserved as

graphics memory.

DVMT Mode

EFAULT

Graphics memory is dynamically allocated

according to the system and graphics needs.

Combo Mode

A fixed portion of graphics memory is reserved as

graphics memory. If more memory is needed,

graphics memory is dynamically allocated

according to the system and graphics needs.

Содержание KINO-945GSE3



















































































































































































Результаты поиска

Содержание KINO-945GSE3

Отзывы:

IEI Technology KINO-945GSE3, Руководство пользователя, Страница: 126 / 178

Результаты поиска

Содержание KINO-945GSE3

Отзывы: