IEI Technology KINO-945GSE3 Скачать руководство пользователя страница 127

Страница: 127 / 178

KINO-945GSE3 User Manual

Page 113

DVMT/FIXED Memory [128 MB]

Use the

DVMT/FIXED Memory

option to specify the maximum amount of memory that

can be allocated as graphics memory. This option can only be configured for if

DVMT

Mode

Fixed Mode

is selected in the

DVMT Mode Selec

t option. If

Combo Mode

selected, the maximum amount of graphics memory is 128 MB. Configuration options are

listed below.

128

Default

Boot Display Device [Auto]

Use the

Boot Display Device

option to select the display device used by the system

when it boots. Configuration options are listed below.

Auto

EFAULT

CRT

LFP

LVDS1 Panel Type

Use the

LVDS1 Panel Type

to determine the LCD panel resolution. Configuration options

are listed below:

640 x 480 18b

800 x 480 18b

800 x 600 18b

1024 x 768 18b

1280 x 1024 36b

1400 x 1050 36b

1440 x 900 36b

1600 x 1200 36b

H/W

Содержание KINO-945GSE3



















































































































































































Результаты поиска

Содержание KINO-945GSE3

Отзывы:

IEI Technology KINO-945GSE3, Руководство пользователя, Страница: 127 / 178

Результаты поиска

Содержание KINO-945GSE3

Отзывы: