IEI Technology KINO-945GSE3 Скачать руководство пользователя страница 76

Страница: 76 / 178

KINO-945GSE3 User Manual

Page 62

4.6.2 LAN Connection (Single Connector)

There are two external RJ-45 LAN connectors. The RJ-45 connectors enable connection

to an external network. To connect a LAN cable with an RJ-45 connector, please follow

the instructions below.

Step 1:

Locate the RJ-45 connectors

. The locations of the USB connectors are shown

Chapter 4

Step 2:

Align the connectors.

Align the RJ-45 connector on the LAN cable with one of

the RJ-45 connectors on the KINO-945GSE3. See Figure 4-16.

Figure 4-16: LAN Connection

Step 3:

Insert the LAN cable RJ-45 connector.

Once aligned, gently insert the LAN

cable RJ-45 connector into the on-board RJ-45 connector.

Step 0:

4.6.3 PS/2 Keyboard and Mouse Connection

The KINO-945GSE3 has a dual PS/2 connector on the external peripheral interface panel.

The dual PS/2 connector is used to connect to a keyboard and mouse to the system.

Follow the steps below to connect a keyboard and mouse to the KINO-945GSE3.

Содержание KINO-945GSE3



















































































































































































Результаты поиска

Содержание KINO-945GSE3

Отзывы:

IEI Technology KINO-945GSE3, Руководство пользователя, Страница: 76 / 178

Результаты поиска

Содержание KINO-945GSE3

Отзывы: