IEI Technology KINO-945GSE3 Скачать руководство пользователя страница 70

Страница: 70 / 178

KINO-945GSE3 User Manual

Page 56

Figure 4-10: USB Power Supply Type Setting Jumper Pinout Locations

4.4 Chassis Installation

4.4.1 Airflow

WARNING:

Airflow is critical for keeping components within recommended

operating temperatures. The chassis should have fans and vents as

necessary to keep things cool.

The KINO-945GSE3 must be installed in a chassis with ventilation holes on the sides

allowing airflow to travel through the heat sink surface. In a system with an individual

power supply unit, the cooling fan of a power supply can also help generate airflow

through the board surface.

4.4.2 Motherboard Installation

To install the KINO-945GSE3 motherboard into the chassis please refer to the reference

material that came with the chassis.

4.5 Internal Peripheral Device Connections

This section outlines the installation of peripheral devices to the onboard connectors.

Содержание KINO-945GSE3



















































































































































































Результаты поиска

Содержание KINO-945GSE3

Отзывы:

IEI Technology KINO-945GSE3, Руководство пользователя, Страница: 70 / 178

Результаты поиска

Содержание KINO-945GSE3

Отзывы: