IEI Technology KINO-945GSE3 Скачать руководство пользователя страница 16

Страница: 16 / 178

KINO-945GSE3 User Manual

Page 2

1.1 Introduction

Figure 1-1: KINO-945GSE3

The KINO-945GSE3 Mini-ITX motherboards are embedded 45 nm Intel® Atom™

processor platforms. The Intel® Atom™ processor N270 embedded on the

KINO-945GSE3 has a 1.60 GHz clock speed, a 533 MHz FSB and a 512 KB L2 cache.

The KINO-945GSE3 supports one 200-pin 400/533 MHz 2.0 GB (max.) DDR2 SDRAM

SO-DIMM. The KINO-945GSE3 comes with an 18-bit dual-channel LVDS connector, a

VGA port, a HDTV-out connector, and a DVI-D port. The KINO-945GSE3 also comes with

two PCI Express (PCIe) Gigabit Ethernet (GbE) ports, a RS-232 serial port (eight

additional serial ports by internal connectors) and a RS-232/422/485 connector, four USB

ports and two additional USB ports by internal connector. Two SATA connectors, a

parallel ATA (IDE) and a CompactFlash® slot provide storage options to the

KINO-945GSE3.

Содержание KINO-945GSE3



















































































































































































Результаты поиска

Содержание KINO-945GSE3

Отзывы:

IEI Technology KINO-945GSE3, Руководство пользователя, Страница: 16 / 178

Результаты поиска

Содержание KINO-945GSE3

Отзывы: