IEI Technology KINO-945GSE3 Скачать руководство пользователя страница 117

Страница: 117 / 178

KINO-945GSE3 User Manual

Page 103

5.5 Boot

Use the

Boot

menu (

BIOS Menu 15

) to configure system boot options.

BIOS SETUP UTILITY

Main

Advanced

PCIPNP

Boot

Security

Chipset

Power

Exit

Boot Settings

⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯

> Boot Settings Configuration

> Boot Device Priority
> Hard Disk Drives
> CD/DVD Drives
> Removable Drives

Configure settings
during system boot.

Select

Screen

↑

↓

Select

Item

Enter Go to SubScreen
F1 General

Help

F10

Save and Exit

ESC Exit

BIOS Menu 15: Boot

5.5.1 Boot Settings Configuration

Use the

Boot Settings Configuration

menu (

BIOS Menu 16

) to configure advanced

system boot options.

BIOS SETUP UTILITY

Main

Advanced

PCIPNP

Boot

Security

Chipset

Power

Exit

Boot Settings Configuration

⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯

Quick Boot

[Enabled]

Quiet Boot

[Enabled]

AddOn ROM Display Mode

[Force BIOS]

Bootup Num-Lock

[On]

Boot from LAN Support

[Disabled]

Spread Spectrum Function

[Disabled]

Allows BIOS to skip
certain tests while
booting. This will
decrease the time needed
to boot the system.

Select

Screen

↑

↓

Select

Item

Enter Go to SubScreen
F1 General

Help

F10

Save and Exit

ESC Exit

BIOS Menu 16: Boot Settings Configuration

Содержание KINO-945GSE3



















































































































































































Результаты поиска

Содержание KINO-945GSE3

Отзывы:

IEI Technology KINO-945GSE3, Руководство пользователя, Страница: 117 / 178

Результаты поиска

Содержание KINO-945GSE3

Отзывы: