IEI Technology KINO-945GSE3 Скачать руководство пользователя страница 90

Страница: 90 / 178

KINO-945GSE3 User Manual

Page 76

Disabled D

EFAULT

Allows hard disks to be overwritten

Enabled

Prevents hard disks from being overwritten

IDE Detect Time Out (Sec) [35]

Use the

IDE Detect Time Out (Sec)

BIOS to specify the maximum time (in seconds) the

AMI BIOS can search for IDE devices. This allows fine-tuning of the settings to allow for

faster boot times. The following configuration options are available.

seconds

EFAULT

seconds

The best setting to use if the onboard IDE controllers are set to a specific IDE disk drive in

the AMIBIOS is “0 seconds” and a large majority of ultra ATA hard disk drives can be

detected well within “5 seconds”.

5.3.2.1 IDE Master, IDE Slave

Use the

IDE Master

and

IDE Slave

configuration menu to view both primary and

secondary IDE device details and configure the IDE devices connected to the system.

Содержание KINO-945GSE3



















































































































































































Результаты поиска

Содержание KINO-945GSE3

Отзывы:

IEI Technology KINO-945GSE3, Руководство пользователя, Страница: 90 / 178

Результаты поиска

Содержание KINO-945GSE3

Отзывы: