IEI Technology KINO-945GSE3 Скачать руководство пользователя страница 50

Страница: 50 / 178

KINO-945GSE3 User Manual

Page 36

3.4.1 Audio Connector

CN Label:

AUDIO1

CN Type:

Audio jacks

CN Location:

See

Figure 3-20

The audio jacks connect to external audio devices.

Line Out port (Lime):

Connects to a headphone or a speaker. With

multi-channel configurations, this port can also connect to front speakers.

Microphone (Pink):

Connects a microphone.

Figure 3-21: Audio Connector

3.4.2 DVI Connector

CN Label:

DVI1

CN Type:

DVI connector

CN Location:

See

Figure 3-20

CN Pinouts:

See

Figure 3-22

and

Table 3-21

The 24-pin Digital Visual Interface (DVI) connector connects to high-speed,

high-resolution digital displays. The DVI-I connector supports both digital and analog

signals.

Pin

Description

Pin

Description

Pin

Description

TMDS Data2-

TMDS Data1-

TMDS Data0-

TMDS Data2+

TMDS Data1+

TMDS Data0+

GND

N/C

Содержание KINO-945GSE3



















































































































































































Результаты поиска

Содержание KINO-945GSE3

Отзывы:

IEI Technology KINO-945GSE3, Руководство пользователя, Страница: 50 / 178

Результаты поиска

Содержание KINO-945GSE3

Отзывы: