IEI Technology KINO-945GSE3 Скачать руководство пользователя страница 146

Страница: 146 / 178

KINO-945GSE3 User Manual

Page 132

B.2.5 Create Factory Default Image

NOTE:

Before creating the factory default image, please configure the system

to a factory default environment, including driver and application

installations.

To create a factory default image, please follow the steps below.

Step 1:

Turn on the system. When the following screen displays (

Figure B-7

), press the

> key to access the recovery tool. The message will display for 10 seconds,

please press F3 before the system boots into the operating system.

Figure B-7: Press F3 to Boot into Recovery Mode

Step 2:

The recovery tool menu appears. Type <

> and press <

Enter

>. (

Figure B-8

)

Figure B-8: Recovery Tool Menu

Step 3:

The About Symantec Ghost window appears. Click

button to continue.

Содержание KINO-945GSE3



















































































































































































Результаты поиска

Содержание KINO-945GSE3

Отзывы:

IEI Technology KINO-945GSE3, Руководство пользователя, Страница: 146 / 178

Результаты поиска

Содержание KINO-945GSE3

Отзывы: