IEI Technology KINO-945GSE3 Скачать руководство пользователя страница 101

Страница: 101 / 178

KINO-945GSE3 User Manual

Page 87

IRQ4

Serial port 6 IRQ address is 4.

IRQ10

EFAULT

Serial port 6 IRQ address is 10.

IR Function

Use the

IR Function

option sets the protocol for IrDA.

Disabled D

EFAULT

IrDA is disabled.

I.6 uS

IrDA protocol is 1.6 uS.

3/16 bit time

IrDA protocol is 3/16 bit time.

Serial Port7 Address [388]

Use the

Serial Port7 Address

option to select the Serial Port 7 base address.

Disabled

No base address is assigned to Serial Port 7

388 D

EFAULT

Serial Port 7 I/O port address is 388.

288

Serial Port 7 I/O port address is 288

380

Serial Port 7 I/O port address is 380.

280

Serial Port 7 I/O port address is 280.

Serial Port7 IRQ [11]

Use the

Serial Port7 IRQ

option to select the interrupt address for serial port 7.

Serial Port8 Address [288]

Use the

Serial Port8 Address

option to select the Serial Port 8 base address.

Disabled

No base address is assigned to Serial Port 8

388

Serial Port 7 I/O port address is 388.

288 D

EFAULT

Serial Port 7 I/O port address is 288

380

Serial Port 7 I/O port address is 380.

Содержание KINO-945GSE3



















































































































































































Результаты поиска

Содержание KINO-945GSE3

Отзывы:

IEI Technology KINO-945GSE3, Руководство пользователя, Страница: 101 / 178

Результаты поиска

Содержание KINO-945GSE3

Отзывы: