IEI Technology KINO-945GSE3 Скачать руководство пользователя страница 104

Страница: 104 / 178

KINO-945GSE3 User Manual

Page 90

VSB

VBAT

5.3.5 Power Configuration

The

Power Configuration

menu (

BIOS Menu 8

) configures the Advanced Configuration

and Power Interface (ACPI) and Power Management (APM) options.

BIOS SETUP UTILITY

Main

Advanced

PCIPNP

Boot

Security

Chipset

Power

Exit

Select AT/ATX Power

[By Hardware]

Auto Power Button Status

[Disable]

> ACPI Configuration
> APM Configuration

Select

Screen

↑

↓

Select

Item

Enter Go to SubScreen
F1 General

Help

F10

Save and Exit

ESC Exit

BIOS Menu 8: Power Configuration

Select AT/ATX Power [BY HARDWARE]

The

Select AT/ATX Power

configures the AT/ATX Power setting.

The AT/ATX power setting is set to AT Power

ATX

The AT/ATX power setting is set to ATX Power

BY HARDWARE D

EFAULT

The AT/ATX power setting is set to the jumper setting

Auto Power Button Status [Disable]

The

Auto Power Button Status

displays the status of the auto power button.

Содержание KINO-945GSE3



















































































































































































Результаты поиска

Содержание KINO-945GSE3

Отзывы:

IEI Technology KINO-945GSE3, Руководство пользователя, Страница: 104 / 178

Результаты поиска

Содержание KINO-945GSE3

Отзывы: