IEI Technology KINO-945GSE3 Скачать руководство пользователя страница 122

Страница: 122 / 178

KINO-945GSE3 User Manual

Page 108

5.5.4 Removable Drives

Use the

Removable Drives

menu (

BIOS Menu 19

) to specify the boot sequence of the

removable drives. Only connected drives are shown.

BIOS SETUP UTILITY

Main

Advanced

PCIPNP

Boot

Security

Chipset

Power

Exit

Hard Disk Drives

⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯

> 1st Drive

[Removable Drive 1]

> 2nd Drive

[Removable Drive 2]

> 3rd Drive

[Removable Drive 3]

Specifies the boot
sequence from the
available devices.

Select

Screen

↑

↓

Select

Item

Enter Go to SubScreen
F1 General

Help

F10

Save and Exit

ESC Exit

BIOS Menu 19: Removable Drives

5.5.5 CD/DVD Drives

Use the

CD/DVD Drives

menu to specify the boot sequence of the available CD/DVD

drives. When the menu is opened, the CD drives and DVD drives connected to the system

are listed as shown below:

1st Drive

[CD/DVD: PM-(part ID)]

2nd Drive

[HDD: PS-(part ID)]

3rd Drive

[HDD: SM-(part ID)]

4th Drive

[HDD: SM-(part ID)]

NOTE:

Only the drives connected to the system are shown. For example, if

only two CDs or DVDs are connected only “

1st Drive

” and “

2nd Drive

”

are listed.

Содержание KINO-945GSE3



















































































































































































Результаты поиска

Содержание KINO-945GSE3

Отзывы:

IEI Technology KINO-945GSE3, Руководство пользователя, Страница: 122 / 178

Результаты поиска

Содержание KINO-945GSE3

Отзывы: