IEI Technology KINO-945GSE3 Скачать руководство пользователя страница 89

Страница: 89 / 178

KINO-945GSE3 User Manual

Page 75

Enhanced D

EFAULT

Configures the on-board ATA/IDE controller to be in

Enhanced mode. In this mode, IDE channels and SATA

channels are separated. This mode supports up to 6

storage devices. Some legacy OS do not support this

mode.

Legacy IDE Channels [PATA Pri, SATA Sec]

SATA Only

Only the SATA drives are enabled.

PATA Pri, SATA Sec

EFAULT

The IDE drives are enabled on the Primary

IDE channel. The SATA drives are enabled on

the Secondary IDE channel.

PATA Pri., PATA Sec

The IDE drives are enabled on the primary

and secondary IDE channels. SATA drives

are disabled.

IDE Master and IDE Slave

When entering setup, BIOS automatically detects the presence of IDE devices. BIOS

displays the status of the automatically detected IDE devices. The following IDE devices

are detected and are shown in the

IDE Configuration

menu:

Primary

IDE

Master

Primary

IDE

Slave

Secondary IDE Master

Secondary IDE Slave

The

IDE Configuration

menu (

BIOS Menu 4

) allows changes to the configurations for the

IDE devices installed in the system. If an IDE device is detected and one of the above

listed four BIOS configuration options are selected, the IDE configuration options shown in

Section 5.3.2.1

appear.

Hard Disk Write Protect [Disabled]

Use the

Hard Disk Write Protect

BIOS option to protect the hard disks from being

overwritten. This menu item is only effective if the device is accessed through the BIOS.

Содержание KINO-945GSE3



















































































































































































Результаты поиска

Содержание KINO-945GSE3

Отзывы:

IEI Technology KINO-945GSE3, Руководство пользователя, Страница: 89 / 178

Результаты поиска

Содержание KINO-945GSE3

Отзывы: