IEI Technology KINO-945GSE3 Скачать руководство пользователя страница 108

Страница: 108 / 178

KINO-945GSE3 User Manual

Page 94

Enabled

If selected, the following appears with values that

can be selected:

RTC Alarm Date (Days)

System Time

After setting the alarm, the computer turns itself on

from a suspend state when the alarm goes off.

Resume on PCI-Express WAKE# [Enabled]

The

Resume on PCI-Express WAKE#

BIOS option specifies if the system is roused from

a suspended or standby state when there is activity on the PCI-Express bus.

Disabled

Wake event not generated by PCI-Express activity

Enabled D

EFAULT

Wake event generated by PCI-Express activity

5.3.7 Remote Access Configuration

Use the

Remote Access Configuration

menu (

BIOS Menu 11

) to configure remote

access parameters. The

Remote Access Configuration

is an AMIBIOS feature and

allows a remote host running a terminal program to display and configure the BIOS

settings.

BIOS SETUP UTILITY

Main

Advanced

PCIPNP

Boot

Security

Chipset

Power

Exit

Configure Remote Access type and parameters

⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯

Remote Access

[Disabled]

Serial port number

[COM1]

Base Address, IRQ

[3F8H, 4]

Serial Port Mode

[115200 8,n,1]

Redirection After BIOS POST

[Always]

Terminal Type

[ANSI]

Select

Screen

↑

↓

Select

Item

Enter Go to SubScreen
F1 General

Help

F10

Save and Exit

ESC Exit

BIOS Menu 11: Remote Access Configuration

Содержание KINO-945GSE3



















































































































































































Результаты поиска

Содержание KINO-945GSE3

Отзывы:

IEI Technology KINO-945GSE3, Руководство пользователя, Страница: 108 / 178

Результаты поиска

Содержание KINO-945GSE3

Отзывы: