IEI Technology KINO-945GSE3 Скачать руководство пользователя страница 111

Страница: 111 / 178

KINO-945GSE3 User Manual

Page 97

The VT100 Terminal Definition is the standard convention used to configure and conduct

emergency management tasks with UNIX-based servers. VT100 does not support all keys

on the standard PC 101-key layout, however. The VT-UTF8 convention makes available

additional keys that are not provided by VT100 for the PC 101 keyboard.

Disabled D

EFAULT

Disables the VT-UTF8 terminal keys

Enabled

Enables the VT-UTF8 combination key. Support for

ANSI/VT100 terminals

5.3.8 USB Configuration

Use the

USB Configuration

menu (

BIOS Menu 12

) to read USB configuration

information and configure the USB settings.

BIOS SETUP UTILITY

Main

Advanced

PCIPNP

Boot

Security

Chipset

Power

Exit

USB Configuration

⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯

Module Version – 2.24.3-13.4

USB Devices Enabled:
None

USB Functions

[Enabled]

USB 2.0 Controller

[Enabled]

Legacy USB Support

[Enabled]

USB 2.0 Controller Mode

[HiSpeed]

Enables USB host
controllers

Select

Screen

↑

↓

Select

Item

Enter Go to SubScreen
F1 General

Help

F10

Save and Exit

ESC Exit

BIOS Menu 12: USB Configuration

USB Configuration

The

USB Configuration

field shows the system USB configuration. The items listed are:

Module Version: x.xxxxx.xxxxx

USB Devices Enabled

The

USB Devices Enabled

field lists the USB devices that are enabled on the system

Содержание KINO-945GSE3



















































































































































































Результаты поиска

Содержание KINO-945GSE3

Отзывы:

IEI Technology KINO-945GSE3, Руководство пользователя, Страница: 111 / 178

Результаты поиска

Содержание KINO-945GSE3

Отзывы: