IEI Technology KINO-945GSE3 Скачать руководство пользователя страница 115

Страница: 115 / 178

KINO-945GSE3 User Manual

Page 101

BIOS SETUP UTILITY

Main

Advanced

PCIPNP

Boot

Security

Chipset

Power

Exit

Advanced PCI/PnP Settings

⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯

WARNING: Setting wrong values in below sections
may cause system to malfunction
IRQ3

[Reserved]

IRQ4

[Reserved]

IRQ5

[Available]

IRQ7

[Available]

IRQ9

[Available]

IRQ10

[Reserved]

IRQ11

[Reserved]

IRQ14

[Available]

IRQ15

[Available]

DMA Channel 0

[Available]

DMA Channel 1

[Available]

DMA Channel 3

[Available]

DMA Channel 5

[Available]

DMA Channel 6

[Available]

DMA Channel 7

[Available]

Reserved Memory Size

[Disabled]

Available: Specified IRQ
is available to be use
the PCI/PnP devices
Reserved: Specified IRQ
is reserved for use by
legacy ISA devices

Select

Screen

↑

↓

Select

Item

Enter Go to SubScreen
F1 General

Help

F10

Save and Exit

ESC Exit

BIOS Menu 14: PCI/PnP Configuration

IRQ# [Available]

Use the

IRQ#

address to specify what IRQs can be assigned to a particular peripheral

device.

Available D

EFAULT

The specified IRQ is available to be used by

PCI/PnP devices

Reserved

The specified IRQ is reserved for use by Legacy ISA

devices

Available IRQ addresses are:

IRQ3

IRQ4

IRQ5

IRQ7

Содержание KINO-945GSE3



















































































































































































Результаты поиска

Содержание KINO-945GSE3

Отзывы:

IEI Technology KINO-945GSE3, Руководство пользователя, Страница: 115 / 178

Результаты поиска

Содержание KINO-945GSE3

Отзывы: