IEI Technology KINO-945GSE3 Скачать руководство пользователя страница 116

Страница: 116 / 178

KINO-945GSE3 User Manual

Page 102

IRQ9

IRQ10

IRQ

DMA Channel# [Available]

Use the

DMA Channel#

option to assign a specific DMA channel to a particular PCI/PnP

device.

Available D

EFAULT

The specified DMA is available to be used by

PCI/PnP devices

Reserved

The specified DMA is reserved for use by Legacy

ISA devices

Available DMA Channels are:

DM Channel 0

DM Channel 1

DM Channel 3

DM Channel 5

DM Channel 6

DM Channel 7

Reserved Memory Size [Disabled]

Use the

Reserved Memory Size

BIOS option to specify the amount of memory that

should be reserved for legacy ISA devices.

Disabled D

EFAULT

No memory block reserved for legacy ISA devices

16K

16 KB reserved for legacy ISA devices

32K

32 KB reserved for legacy ISA devices

64K

54 KB reserved for legacy ISA devices

Содержание KINO-945GSE3



















































































































































































Результаты поиска

Содержание KINO-945GSE3

Отзывы:

IEI Technology KINO-945GSE3, Руководство пользователя, Страница: 116 / 178

Результаты поиска

Содержание KINO-945GSE3

Отзывы: