IEI Technology KINO-945GSE3 Скачать руководство пользователя страница 137

Страница: 137 / 178

KINO-945GSE3 User Manual

Page 123

B.1 One Key Recovery Introduction

The IEI one key recovery is an easy-to-use front end for the Norton Ghost system backup

and recovery tool. The one key recovery provides quick and easy shortcuts for creating a

backup and reverting to that backup or for reverting to the factory default settings.

To create the system backup the main storage device must be split into two partitions

(three partitions for Linux). The first partition will be for the operating system, while the

second partition will be invisible to the operating system and contain the backup made by

the one key recovery software.

B.1.1 System Requirement

The partition created for recovery images must be big enough to contain both the factory

default image and the user backup image. The size must be calculated before creating the

partitions. Please take the following table as a reference when calculating the size of the

partition.

OS Image after Ghost

Compression Ratio

Windows® 7

7 GB

5 GB

70%

Windows® XPE

776 MB

560 MB

70%

Windows® CE 6.0

36 MB

28 MB

77%

NOTE:

Specialized tools are required to change the partition size if the

operating system is already installed.

B.1.2 Supported Operating System

The recovery CD is compatible with both Microsoft Windows and Linux operating system

(OS). The supported OS versions are listed below.

Содержание KINO-945GSE3



















































































































































































Результаты поиска

Содержание KINO-945GSE3

Отзывы:

IEI Technology KINO-945GSE3, Руководство пользователя, Страница: 137 / 178

Результаты поиска

Содержание KINO-945GSE3

Отзывы: