IEI Technology KINO-945GSE3 Скачать руководство пользователя страница 105

Страница: 105 / 178

KINO-945GSE3 User Manual

Page 91

5.3.5.1 ACPI Configuration

Use the

ACPI Configuration

menu (

BIOS Menu 9

) to select the ACPI state when the

system is suspended.

BIOS SETUP UTILITY

Main

Advanced

PCIPNP

Boot

Security

Chipset

Power

Exit

ACPI Settings

⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯

Suspend Mode

[S1 (POS)]

Select

Screen

↑

↓

Select

Item

Enter Go to SubScreen
F1 General

Help

F10

Save and Exit

ESC Exit

BIOS Menu 9: ACPI Settings

Suspend Mode [S1 (POS)]

Use the

Suspend Mode

option to specify the sleep state the system enters when it is not

being used.

S1 (POS) D

EFAULT

The system enters S1 (POS) sleep state. The system

appears off. The CPU is stopped; RAM is refreshed; the

system is running in a low power mode.

5.3.6 APM Configuration

The

APM Configuration

menu (

BIOS Menu 10

) allows the advanced power

management options to be configured.

Содержание KINO-945GSE3



















































































































































































Результаты поиска

Содержание KINO-945GSE3

Отзывы:

IEI Technology KINO-945GSE3, Руководство пользователя, Страница: 105 / 178

Результаты поиска

Содержание KINO-945GSE3

Отзывы: