Endress+Hauser TopClean S CPC 30, Руководство по эксплуатации

Страница: 133 / 146

TopClean S CPC 30 11 Appendix
Hauser 133
CAL
C07-CPC300xx-19-06-08-en-010.EPS
Window info calibra-
tion type
:
Cal with Enter
spec. Buffer:
(selected in:PARAM\
Set up 1\Calibration\
Manual calibration)
for Cal with Manual
Buffer:
For Calibration with
Buffer Table /
Auto Buffer recogn.
for Calibration with
Enter Data abs.:
For Calibration with
Calibration abs.:
Window info calibra-
tion type
:
(selected in:PARAM\
Set up 1\Calibration\
Manual calibration)
Window i
rel.:
For Calibration with
Enter Data rel.:
Calibration with
50% switch point:
nfo calibra-
tion type
:
(for Calibration with
Enter Data abs. and
with Calibration abs.
see above)
for Calibration with
Calibration
(selected in:PARAM\
Set up 1\Calibration\
Manual calibration)
Calibration
Reject
Recalibrate
Accept
Stability check
Buffer 1
If stable:
press E
Stability check
Buffer 1
If stable:
press E
Calibration info
Elektrode
50% Voltage 225mV/pH
20
8
% Voltage 600mV/pH
0% Voltage- 600mV/pH
2
Stability check
Buffer
If stable:
press E
Note:
voltage range
too small
Data input:
Zero point
07.00pH
(-2.00...16.00pH)
Enter temperature
at which zero point
determined.
and slope have been
025.0°C
(-20.0...150.0°C)
Edit Slope
57.19mV/pH
(5.00...99.00mV/pH)
Calibration
Reject
Repeat calibration
Accept
Calibration
Accept
Reject
Recalibrate
Calibration
Reject
Recalibrate
Accept
Note:
Elektrode
submersed?
Note:
Elektrode
submersed?
Note:
Elektrode
submersed?
Note:
Elektrode
submersed?
Calibration
Reject
Recalibrate
Accept
Note:
Elektrode
submersed?
Note:
Elektrode
submersed?
Edit Buffer 2
Temp: 25.0°C
07.00 pH
(–2.00...16.00pH)
Identified Buffers:
Buffer 1:
Buffer 2:
Buffertype:E+H
(or calibration end)
Elektrode Info:
Zero point
Condition
Slope
Condition
Elektrode condition
Elektrode 1
good
Note: Start
1st buffer
Immerse Elektrode
in buffer 1
Elektrode condition
Elektrode
good
Edit Buffer 1
Temp: 25.0°C
07.00 pH
(–2.00...16.00pH)
Note:
Calibration result
invalid-->
Reject
Recalibrate
Note:
Calibration result
invalid-->
Reject
Recalibrate
Note: Start
1st Buffer
Immerse Elektrode
in buffer 1
Note: Start
1st Buffer
Submerse Elektrode
in Buffer
Note: Start
1st Buffer
Submerse Elektrode
in Buffer
Note: Start
1st Buffer
Submerse Elektrode
in Buffer
Enter Cal. points
1:0...30%: 20%
1: Voltage: 0600 mV
2: 70...100%: 80%
2: Voltage: -0600mV
Note: Start
2st Buffer
Submerse Elektrode
in Buffer
Note: Start
2nd Buffer
Immerse Elektrode
in buffer 2
Note: Start
2nd Buffer
Immerse Elektrode
in buffer 2
Edit Buffer temp..
025.0°C
(only MTC)
(-20.0...150.0°C)
Edit Buffer temp..
025.0°C
(only MTC)
(-20.0...150.0°C)
Enter Offset
0000mV
(-1500...1500.0mV)
Enter Buffer
0225mV
(-1500...1500mV)
2
10%
Enter Buffer
(0...30%)
Calibration info
Elektrode
Offset 0000mV
good
Note:
Calibration result
not valid
If you press the MEAS
key, a message will
appear asking if you
want to abort the
calibration.
= Code entry required
Sensor mode pH:
Sensor mode Redox abs. (mV):
Sensor mode Redox rel. (%):
Stability check
Buffer 1
If stable:
press E
Stability check
Buffer 2
If stable:
press E
Stability check
Buffer 1
If stable:
press E
Stability check
Buffer 2
If stable:
press E
Calibration
Reject
Recalibrate
Accept
Note:
Elektrode
submersed?
Note:
Elektrode
submersed?
Stability check
Buffer 1
If stable:
press E
Enter Buffer
10%
(0...30%)