Endress+Hauser SpectraSensors SS2000e Скачать руководство пользователя страница 49

Страница: 49 / 114

Operating the Analyzer

Operator’s Manual

–

concentration begins to drop steadily, the permeation device must be replaced.

For details on replacing the permeation device, refer to the Hardware Manual.

Val Start Time

The

Val Start Time

parameter sets the hour of the day for the daily validation

to begin. Enter the required value.

Zero Val Tolerance

The

Zero Val Tolerance

parameter is used to set the maximum acceptable

reading when validating with zero gas. To configure the analyzer for zero gas

set the parameter

Val 1 Concentration

Val 2 Concentration

0.0

. Enter

the required value.

Adjusting Analyzer Reading to Match Specific

Standard(s)

In some instances, the user may wish to adjust the analyzer reading to match

the concentration (or concentrations) of a specific standard (or standards). The

RATA Multiplier

and

RATA Offset

parameters are used to adjust the analyzer

output in the field without affecting the factory calibration. Both parameters are

used when samples from two different concentration standards are available,

whereas only the

RATA Multiplier

parameter is used when a non-zero gas

sample from only one concentration standard is available. If using a zero gas

sample from only one concentration standard, then only the

RATA Offset

parameter should be calculated.

Val Perm Rate Rp

0.33

0:Off >0:ng/min

Val Start Time

Hour of day (0-23)

Zero Val Tolerance

60.0

Enter a value (ppmv)

Содержание SpectraSensors SS2000e



















































































































Результаты поиска

Содержание SpectraSensors SS2000e

Отзывы:

Похожие инструкции для SpectraSensors SS2000e

Бренды по названию

Популярные бренды

Endress+Hauser SpectraSensors SS2000e, Руководство оператора

Результаты поиска

Содержание SpectraSensors SS2000e

Отзывы:

Похожие инструкции для SpectraSensors SS2000e

Бренды по названию

Популярные бренды