Endress+Hauser SpectraSensors SS2000e Скачать руководство пользователя страница 91

Страница: 91 / 114

Operator’s Manual

–

4 - E

THERNET

OMMUNICATIONS

Configuring the Built-in Ethernet Port

The built-in Ethernet port must be properly configured to communicate on a

network or directly with a PC. The Ethernet port has been factory set as follows:

•

IP Address

: 192.168.000.001

•

Telnet (Set-up) Port

: 9999

•

Web Manager (Set-up) Port

: 30718 (Fixed)

•

Serial Data Port

: 10001

The configuration is stored in nonvolatile memory and is retained without

power. The configuration can be changed at any time.

If the IP address or any other setting needs to be changed, the Ethernet port

Setup Mode

can be accessed using a Telnet connection, the Web Manager

locally or over the network.

To configure the built‐in Ethernet port with Telnet

From your computer Windows desktop, click

Start

followed by

Run

(usually located in the lower right side of the

Start Menu

Type the following command:

telnet 192.168.000.001 9999

Click

to establish a Telnet connection. The following message

appears:

MAC address XXXXXXXXXXXX

(E.g., 00204A808BE8)

Software version

V6.3.0.3RC3 (061110)

(Version may vary by system)

Press Enter for Setup Mode

To enter

Setup Mode

, press

Enter

within 5 seconds. The

configuration settings display, followed by the

Change Setup

menu.

Change Setup:

0 Server

1 Channel 1

5 Expert

6 Security

7 Defaults

8 Exit without save

9 Save and exit

Your choice?

Select an option on the menu by entering the number of the option

in the “Your choice?” field and pressing

Enter

The two menus recommended for review are “0 Server” and “1

Channel 1”. Bypass the other options listed in the menu.

Содержание SpectraSensors SS2000e



















































































































Результаты поиска

Содержание SpectraSensors SS2000e

Отзывы:

Похожие инструкции для SpectraSensors SS2000e

Бренды по названию

Популярные бренды

Endress+Hauser SpectraSensors SS2000e, Руководство оператора

Результаты поиска

Содержание SpectraSensors SS2000e

Отзывы:

Похожие инструкции для SpectraSensors SS2000e

Бренды по названию

Популярные бренды