Endress+Hauser SpectraSensors SS2000e Скачать руководство пользователя страница 55

Страница: 55 / 114

Operating the Analyzer

Operator’s Manual

–

Scaling and Calibrating the Current Loop Signal

The 4-20 mA current loop signals are most conveniently scaled and calibrated

at the receiving end (RTU, flow computer, etc.).

To scale the receiver’s output, the analyzer’s current loop output is forced to

4 mA (0%) and 20 mA (100%) using the

4-20 mA Test

parameter. The

receiver is adjusted to read “0” and “Full Scale,” respectively.

To scale the current loop signal

Make sure the current loop is connected and the receiver is set for

the analyzer to source the current.

Set the

4-20 mA Test

parameter to 0% (see

“To change

parameters in Mode 2”

on page 2-15).

Enter

Mode 5

by pressing the

key followed by the

key to force

the loop current to 4 mA.

Adjust the receiver calibration control to read the appropriate value.

A current loop output of 4 mA represents the value set in

AO 4 mA

Value

Set the

4-20 mA Test

parameter to 100%.

Enter

Mode 5

by pressing the

key followed by the

key to force

the loop current to 20 mA.

Adjust the receiver calibration controls for the appropriate value. A

current loop output of 20 mA represents the value set in

AO 20 mA

Value

If needed, repeat steps 2-7 to obtain an accurate calibration over the

range.

After obtaining an accurate calibration of the current loop receiver,

press the

key followed by the

key to return to

Normal Mode.

The 4-20 mA current loop output is factory set to source current.

To change the 4-20 mA current loop output from source to sink,

refer to the section called “

Changing the 4-20 mA Current

Loop Mode”

in the Hardware Manual.

Be sure to work in a non-hazardous area while handling any

electrical connector.

When the # key is pressed, measurement will be suspended until

a new mode is established. The only modes that produce

measurements are

Mode 1

Mode 6

Mode 7

Mode 8

Содержание SpectraSensors SS2000e



















































































































Результаты поиска

Содержание SpectraSensors SS2000e

Отзывы:

Похожие инструкции для SpectraSensors SS2000e

Бренды по названию

Популярные бренды

Endress+Hauser SpectraSensors SS2000e, Руководство оператора

Результаты поиска

Содержание SpectraSensors SS2000e

Отзывы:

Похожие инструкции для SpectraSensors SS2000e

Бренды по названию

Популярные бренды