Endress+Hauser SpectraSensors SS2000e Скачать руководство пользователя страница 99

Страница: 99 / 114

Ethernet Communications

Operator’s Manual

–

connect to any others. If this connection fails, the unit

continues to scroll through the table until it connects to

another IP in the host list.

The host list is disabled for Manual Mode and for Modem

Mode. The unit will not accept a data connection from a

remote device when the host list option is enabled.

–

LED

: Select

Blink

for the status LEDs to blink upon

connection or

None

for no LED output.

•

Disconnect Mode

–

On Mdm_Ctrl_In Drop

: Set to

Yes

for the network

connection to or from the serial port to disconnect (drop)

when

Modem Control In

transitions from an asserted state

to not asserted state. The default setting is

–

Hard Disconnect

: When set to

Yes

, the TCP connection

closes even if the remote site does not acknowledge the

disconnect request.

–

Check EOT

(

Ctrl-D

): Select

Yes

to drop the connection

when

Ctrl-D

Hex 04

is detected. Both

Telnet Com Port

Cntrl

and

Check EOT

(

Ctrl-D

) must be enabled for

Disconnect with EOT

to function properly.

Ctrl-D

is only

detected going from the serial port to the network. The

default setting is

–

Inactivity Timeout

: Use this parameter to set an inactivity

timeout. The unit drops the connection if there is no activity

on the serial line before the set time expires. Enter time in

the format “mm:ss”, where “m” is the number of minutes and

“s” is the number of seconds. To disable the inactivity

timeout, enter

00:00

When finished, click the

button.

General Information for Configuring Ethernet

For more information on configuring your computer for Ethernet connection,

please refer to the Lantronix website below.

•

https://www.lantronix.com/products/xport-direct/#docs-downloads

Содержание SpectraSensors SS2000e



















































































































Результаты поиска

Содержание SpectraSensors SS2000e

Отзывы:

Похожие инструкции для SpectraSensors SS2000e

Бренды по названию

Популярные бренды

Endress+Hauser SpectraSensors SS2000e, Руководство оператора

Результаты поиска

Содержание SpectraSensors SS2000e

Отзывы:

Похожие инструкции для SpectraSensors SS2000e

Бренды по названию

Популярные бренды