Endress+Hauser SpectraSensors SS2000e Скачать руководство пользователя страница 15

Страница: 15 / 114

Operator’s Manual

–

2 - O

PERATING

THE

NALYZER

Firmware Version

Each SpectraSensors analyzer operates with a specific version of firmware. The

firmware version for each analyzer is listed in the associated system calibration

report, and displays upon start up of the analyzer. The operation instructions

provided in this chapter are intended for the NS 5.14 firmware version.

Powering Up the Analyzer

After mounting the analyzer, connecting the power wires, connecting the gas

lines, connecting the (optional) output signal wires and checking for leaks, you

are ready to power up the analyzer.

To power up the analyzer

Power up the analyzer by energizing the circuit to the analyzer.

For systems with a heated enclosure, confirm that the sample

system enclosure is heated to approximately the specified

temperature by observing the temperature reading on the door

mounted thermometer.

The analyzer is designed to be a stationary measuring device. It

should be securely mounted during normal operation.

The laser housing labels on the flanges of the sample cell warn

about exposure to laser radiation inside. Never open the sample

cell unless directed to do so by Service and the analyzer power is

turned off. Refer to

“Service Contact”

on page A-4

The optical head has a seal and “WARNING” sticker to prevent

inadvertent tampering with the device. Do not attempt to

compromise the seal of the optical head assembly. Doing so will

result in loss of device sensitivity and inaccurate measurement

data. Repairs can then only be performed by the factory and are

not covered under warranty.

Refer to the figures for the analyzer electronic control boards in

the Hardware Manual for fuse location. If you need to replace a

fuse, use only the same type and rating of fuse as the original as

listed in the analyzer fuse specifications table in the Hardware

Manual.

Содержание SpectraSensors SS2000e



















































































































Результаты поиска

Содержание SpectraSensors SS2000e

Отзывы:

Похожие инструкции для SpectraSensors SS2000e

Бренды по названию

Популярные бренды

Endress+Hauser SpectraSensors SS2000e, Руководство оператора

Результаты поиска

Содержание SpectraSensors SS2000e

Отзывы:

Похожие инструкции для SpectraSensors SS2000e

Бренды по названию

Популярные бренды