Endress+Hauser SpectraSensors SS2000e Скачать руководство пользователя страница 7

Страница: 7 / 114

Table of Contents

4900002262 rev. B 3-23-21

iii

Mode 1 data string . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1

To capture and save data from the serial port . . . . . . . . . . . . . . . . . . . . . . . 3-5

To read diagnostic data with HyperTerminal . . . . . . . . . . . . . . . . . . . . . . . . 3-5

Mode 6 data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-6

Viewing Diagnostic Data with Microsoft Excel . . . . . . . . . . . . . . . . . . . . . . . . . . 3-8

To import the data file into Excel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-8

Modbus Communications Protocol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-12

Framing/Protocol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-12

Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-12

Reading/Writing in Daniel Modbus mode. . . . . . . . . . . . . . . . . . . . . . . . . . 3-12

Reading/Writing in Gould Modbus mode . . . . . . . . . . . . . . . . . . . . . . . . . . 3-12

Endianness . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-13

To enable Modbus communications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-13

Addressing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-14

Modbus accessible parameter definitions . . . . . . . . . . . . . . . . . . . . . . . . . 3-20

4: Ethernet Communications

Configuring the Built-in Ethernet Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1

To configure the built-in Ethernet port with Telnet . . . . . . . . . . . . . . . . . . . . 4-1

To configure the built-in Ethernet port with the Web Manager . . . . . . . . . . . . 4-2

Network Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-5

Automatic IP address configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-5

To assign an IP address automatically . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-5

Static IP address configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-5

To assign an IP address manually . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-6

Ethernet configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-6

To specify how data will be transmitted . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-6

Channel Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-7

To configure a channel’s TCP settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-7

General Information for Configuring Ethernet . . . . . . . . . . . . . . . . . . . . . . . . . . 4-9

Appendix A: Troubleshooting

Contamination . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-1

Excessive Sampling Gas Temperatures and Pressures . . . . . . . . . . . . . . . . . . . . A-1

Peak Tracking Reset Procedure. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-1

To reset the Peak Tracking function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-2

Instrument Problems. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-3

Service Contact . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-4

Before contacting Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-5

Disclaimers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-5

Index

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Index-1

Содержание SpectraSensors SS2000e



















































































































Результаты поиска

Содержание SpectraSensors SS2000e

Отзывы:

Похожие инструкции для SpectraSensors SS2000e

Бренды по названию

Популярные бренды

Endress+Hauser SpectraSensors SS2000e, Руководство оператора

Результаты поиска

Содержание SpectraSensors SS2000e

Отзывы:

Похожие инструкции для SpectraSensors SS2000e

Бренды по названию

Популярные бренды