Endress+Hauser SpectraSensors SS2000e Скачать руководство пользователя страница 26

Страница: 26 / 114

NS 5.14 Firmware

–

4900002262 rev. B 3-23-21

Table 2-1

Typical values for parameter setpoints (Continued)

Parameter

Setting

Function

RATA

(Relative Accuracy Test

Audit)

0 or 1

Default: 0

Enables or disables adjustment

factors.

RATA Multiplier

-1.E+06 to 1.E+06

Default 1.0

Slope adjustment factor.

RATA Offset

-1.E+06 to 1.E+06

Default 0.0

Offset adjustment factor.

Update RATA

0 or 1

Default: 0

Updates RATA Multiplier and

Offset to automatically

calculated values.

Peak Tracking

0, 1 or 2

Default: 0

Sets peak tracking capability to

off, on or reset.

Keypad Watchdog

< 5:Off, >=5:Secs

Default = 10

The time-out on the Mode

screen before the analyzer

automatically reverts to Normal

Mode.

Set Time - Hour

0 to 23

Default: 0

Sets the current hour.

Set Time - Minute

0 to 59

Default: 0

Sets the current minute.

Set Time - Day

1 to 31

Default: 1

Sets the present day.

Set Time - Month

1 to 12

Default: 1

Sets the present month.

Set Time - Year

2006 to 2144

Default: 2017

Sets the present year.

General Alarm DO

0, 1, or 2

Default = 0

Sets the alarm mode (latching

or non-latching) and resets the

general alarm once activated.

DO Alarm Setup

4.29E+09

Default = 8192

Sets the functionality of the

secondary digital output.

Low Alarm Setpoint

-1.E+06 to 1.E+06

Default = -10000

Sets the low alarm threshold

for moving average.

High Alarm Setpoint

-1.E+06 to 1.E+06

Default = 10000

Sets the high alarm threshold

for moving average.

AO 4-20 mA Test

0.0 to 100.0

Default: 0.0

Sets the 4-20 mA output to a

percentage of full scale.

4-20 mA Alarm Action

0, 1, 2 or 3

Default: 0

Sets the current loop state

upon alarm condition.

Содержание SpectraSensors SS2000e



















































































































Результаты поиска

Содержание SpectraSensors SS2000e

Отзывы:

Похожие инструкции для SpectraSensors SS2000e

Бренды по названию

Популярные бренды

Endress+Hauser SpectraSensors SS2000e, Руководство оператора

Результаты поиска

Содержание SpectraSensors SS2000e

Отзывы:

Похожие инструкции для SpectraSensors SS2000e

Бренды по названию

Популярные бренды